Products tagged with 'stainless steel'
JET WJ SERIES - WJ-201-X-EM/6
WJ-201-X-EM/6
WILO JET WJ SERIES - WJ-201-X-EM/6
MATERIAL STAINLESS STEEL
HP 0.50
VOLTAGE 220 V - 60HZ
RPM 3450
₱17,500.00
₱10,875.00
JET WJ SERIES - WJ-202-X-EM/6/B
WJ-202-X-EM/6/B
WILO PUMP
WJ-202-X-EM 6/B
SELF PRIMING PUMP
STAINLESS STEEL
0.75 HP
VOLTAGE 220 V - 60 HZ
RPM 3450
₱11,500.00
JET WJ SERIES - WJ-203-X-EM/6/B
WJ-203-X-EM/6/B
WILO JET WJ SERIES - WJ-203-X-EM/6/B
STAINLESS STEEL
1.0 HP
VOLATGE 220 V - 60HZ
RPM 3450
₱12,000.00
STAINLESS STEEL SUBMERSIBLE BOREHOLE MOTOR FOR 4" & 6" WELL CASING DIAMETER - MS4-10-1-1-T
MS4-10-1-1-T
Stainless Steel Submersible Borehole Motor
For 4" & 6" Well Casing Diameter
₱175,000.00
₱21,875.00
STAINLESS STEEL SUBMERSIBLE BOREHOLE MOTOR FOR 4" & 6" WELL CASING DIAMETER - MS4-15-1-1-T
MS4-15-1-1-T
Stainless Steel Submersible
Borehole Motor For 4" & 6" Well
Casing Diameter High Quality Thrust Bearings
The trust bearing is of the kingsburrY type
lubricated by the internal fluid.
During operation a wedge of
water is drawn between the stainless
steel pivot shoes and carbon disc to carry
the thrust load generated by the pump.
Located inside and at the bottom of the motor,
the bearing is sealed away from sand and other
contaminants. Sand Resistant Slinger and Lip Seals
A stainless steel slinger and slinger guide are also
closely fit to help prevent sand entry.
Double rubber seals are installed to prevent
well water and contaminants from entering the motor.
High Reliable Carbon Bearing Two water
lubricated carbon bearings are used as
guide bearings. These have extremely large
surface area and result in extra alignment
support-less whipping and acts as a steady bushing.
Water-Filled Design The motor lubrication is
provided by the internal cooling water consistings
of a water, anti-freeze and anti-rust mixture good
to 30°C (-22°F). This mixture is installed at the factory.
Two water plugs are located near of the top of the motor
and are used by the installer to check the water level or to
the top off needed before installation. Complete Corrosion
and Water-Tight Protection All main motor components are
made of stainless steel: including the can housing
(water tight type motors have baked epoxy coated steel housing),
Shaft and bolts. All other motor parts are coated
with the baked epoxy coating.
₱22,500.00
₱28,125.00
STAINLESS STEEL SUBMERSIBLE BOREHOLE MOTOR FOR 4" & 6" WELL CASING DIAMETER - MS4-20-1-1-T
MS4-20-1-1T
This depends upon the depth of the borehole
to ground level and then the distance from the
ground level to the final end point e.g.
where the water tank is sited. The further the distance,
the higher the pressure requirements of the borehole
pump to prevent the water from trickling out.
Submersible borehole pumps are a type of
submersible pump. They are centrifugal pumps
driven by a submersible motor.
As they usually draw in the fluid directly without a suction line,
they must constantly be submerged in the fluid handled.
Starter borehole pumps can run for up to 24 hours.
However, your everyday borehole pump will run between 6 & 8 hours.
It is not good for your borehole pump to run continuously.
If you run electrical pumps continuously,
your utility bill will skyrocket.
₱22,500.00
₱30,625.00
STAINLESS STEEL SUBMERSIBLE BOREHOLE MOTOR FOR 4" & 6" WELL CASING DIAMETER - MS4-30-1-1-T
MS4-30-1-1-T
The diameter of the borehole is usually around
120 to 160 mm, and its depth can reach up to 300 meters,
although depth of about 40 meters is more common.
Your pump and its control system must also meet the specific
conditions as well as the high demands on reliability.
This depends upon the depth of the borehole to
ground level and then the distance from the ground
level to the final end point e.g. where the water tank is sited.
The further the distance, the higher the pressure requirements
of the borehole pump to prevent the water from trickling out.
Submersible borehole pumps are a type of submersible pump
. They are centrifugal pumps driven by a submersible motor.
As they usually draw in the fluid directly without a suction line,
they must constantly be submerged in the fluid handled.
₱34,500.00
₱43,125.00
STAINLESS STEEL SUBMERSIBLE BOREHOLE MOTOR FOR 4" & 6" WELL CASING DIAMETER - MS4-30-3-2-T
MS4-30-3-2-T
The diameter of the borehole is usually around
120 to 160 mm, and its depth can reach up to 300
meters, although depth of about 40 meters is
more common. Your pump and its control system
must also meet the specific conditions as well
as the high demands on reliability.
This depends upon the depth of the borehole
to ground level and then the distance from the
ground level to the final end point e.g.
where the water tank is sited.
The further the distance, the higher
the pressure requirements of the borehole pump
to prevent the water from trickling out.
Submersible borehole pumps are a type
of submersible pump. They are centrifugal
pumps driven by a submersible motor.
As they usually draw in the fluid directly without a suction line,
they must constantly be submerged in the fluid handled.
₱29,000.00
₱36,250.00
STAINLESS STEEL SUBMERSIBLE BOREHOLE MOTOR FOR 4" & 6" WELL CASING DIAMETER - MS4-50-1-1-T
MS4-50-1-1-T
Stainless Steel Submersible Borehole Motor
For 4" & 6" Well Casing Diameter
High Quality Thrust Bearings
The trust bearing is of the kingsburry type
lubricated by the internal fluid.
During operation a wedge of water is drawn
between the stainless steel pivot shoes and carbon
disc to carry the thrust load generated by the pump.
Located inside and at the bottom of the motor,
the bearing is sealed away from sand and other
contaminants.
Sand Resistant Slinger and Lip Seals
A stainless steel slinger and slinger guide
are also closely fit to help prevent sand entry.
Double rubber seals are installed to prevent
well water and contaminants from entering the motor.
High Reliable Carbon Bearing
Two water lubricated carbon bearings are used
as guide bearings. These have extremely
large surface area and result in extra alignment
support-less whipping and acts as a steady bushing.
Water-Filled Design
The motor lubrication is provided by t
he internal cooling water consistings of a water,
anti-freeze and anti-rust mixture good to 30
°C (-22°F). This mixture is installed at the factory.
Two water plugs are located near of the top of the
motor and are used by the installer to check the
water level or to the top off needed before installation.
Complete Corrosion and Water-Tight Protection
All main motor components are made of stainless steel:
including the can housing (water tight type motors have
baked epoxy coated steel housing), Shaft and bolts.
All other motor parts are coated with the baked epoxy coating.
₱53,200.00
₱66,500.00
STAINLESS STEEL SUBMERSIBLE BOREHOLE MOTOR FOR 4" & 6" WELL CASING DIAMETER - MS4-50-3-2-T
MS4-50-3-2-T
Stainless Steel Submersible Borehole Motor
For 4" & 6" Well Casing Diameter
High Quality Thrust Bearings
The trust bearing is of the kingsburry
type lubricated by the internal fluid.
During operation a wedge of water is
drawn between the stainless steel pivot
shoes and carbon disc to carry the thrust
load generated by the pump.
Located inside and at the bottom
of the motor, the bearing is sealed
away from sand and other contaminants.
Sand Resistant Slinger and Lip Seals
A stainless steel slinger and slinger
guide are also closely fit to help prevent sand entry.
Double rubber seals are installed to prevent wel
l water and contaminants from entering the motor.
High Reliable Carbon Bearing
Two water lubricated carbon bearings are used
as guide bearings.
These have extremely large surface area and result
in extra alignment support-less whipping and acts as a steady bushing.
Water-Filled Design
The motor lubrication is provided by the internal
cooling water consistings of a water, anti-freeze
and anti-rust mixture good to 30°C (-22°F).
This mixture is installed at the factory.
Two water plugs are located near of the
of the motor and are used by the installer to
check the water level or to the top off needed before installation.
Complete Corrosion and Water-Tight Protection
All main motor components are made of stainless steel
: including the can housing (water tight type
motors have baked epoxy coated steel housing),
Shaft and bolts. All other motor parts are coated
with the baked epoxy coating.
₱50,000.00
₱62,500.00
STAINLESS STEEL SUBMERSIBLE BOREHOLE MOTOR FOR 4" & 6" WELL CASING DIAMETER - MS4-75-3-1-T
MS4-75-3-1-T
Stainless Steel Submersible Borehole Motor
For 4" & 6" Well Casing Diameter
High Quality Thrust Bearings
The trust bearing is of the kingsburry
type lubricated by the internal fluid.
During operation a wedge of water is
drawn between the stainless steel pivot
shoes and carbon disc to carry the thrust
load generated by the pump. Located inside
and at the bottom of the motor,
the bearing is sealed away from sand
and other contaminants.
Sand Resistant Slinger and Lip Seals
A stainless steel slinger and slinger
guide are also closely fit to help prevent
sand entry. Double rubber seals are installed
to prevent well water and contaminants from entering the motor.
High Reliable Carbon Bearing
Two water lubricated carbon bearings are used
as guide bearings. These have extremely large
surface area and result in extra alignment support-
less whipping and acts as a steady bushing.
Water-Filled Design
The motor lubrication is provided by the internal
cooling water consistings of a water, anti-freeze and
anti-rust mixture good to 30°C (-22°F). This mixture is
installed at the factory. Two water plugs are located
near of the top of the motor and are used by the installer
to check the water level or to the top off needed before installation.
Complete Corrosion and Water-Tight Protection
All main motor components are made of stainless steel:
including the can housing (water tight type motors have
baked epoxy coated steel housing), Shaft and bolts.
All other motor parts are coated with the baked epoxy coating.
₱75,000.00
₱93,750.00
STAINLESS STEEL SUBMERSIBLE BOREHOLE MOTOR FOR 4" & 6" WELL CASING DIAMETER - MS6-100-3-2-T
MS6-100-3-2-T
Stainless Steel Submersible Borehole Motor
For 4" & 6" Well Casing Diameter
High Quality Thrust Bearings
The trust bearing is of the kingsburry
type lubricated by the internal fluid.
During operation a wedge of water is
drawn between the stainless steel pivot
shoes and carbon disc to carry the thrust
load generated by the pump. Located inside
and at the bottom of the motor, the bearing
is sealed away from sand and other contaminants.
Sand Resistant Slinger and Lip Seals
A stainless steel slinger and slinger guide are also
closely fit to help prevent sand entry. Double rubber
seals are installed to prevent well water and
contaminants from entering the motor.
High Reliable Carbon Bearing
Two water lubricated carbon bearings are used
as guide bearings. These have extremely large surface area and
result in extra alignment support-less whipping and acts as a steady bushing.
Water-Filled Design
The motor lubrication is provided by the internal
cooling water consistings of a water, anti-freeze and
anti-rust mixture good to 30°C (-22°F). This mixture is
installed at the factory. Two water plugs are located
near of the top of the motor and are used by the installer
to check the water level or to the top off needed before installation.
Complete Corrosion and Water-Tight Protection
All main motor components are made of stainless steel:
including the can housing (water tight type motors have
baked epoxy coated steel housing), Shaft and bolts.
All other motor parts are coated with the baked epoxy coating.
₱81,500.00
₱101,875.00