Hand Tools

Socket T - Wrench - 1400M

Plastring Trowel

Quick Release Ratchet Handle - 3/4" DR. X 18"

Ratchet Handle - 1" DR. X 32"

Hand Riveter 10.5"

Quick Release Ratchet Handle 1/2" DR. X 10"

Rachet Handle Quick Release (1/2" DR. X 10" ) (3/8" DR. X 8" ) (1/4" DR. X 5")

Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.

Adjustable Wrench Spanner

Stubby Reversible Handle - 1/2" DR.

Stubby Reversible Handle - 3/8" DR.

Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.

Y-Type Socket Wrench

Impact Socket Extension Bar

Spirit Level

Hans Spark Plug Socket

Hans Spark Plug Socket

PVC Pipe Cutter

Magnetic Spark Plug 1/2" DR. X 13/16" - Inches Size

Magnetic Spark Plug 1/2" DR. X 14MM - Metric Size

Magnetic Spark Plug 1/2"DR X 5/8" - Inches Size

INGCO Claw Hammer HCH80808

PLIERS LOCKING CURVED JAW 250MM/10"

CREW PLIERS CR-V 160MM-ME200029

INGCO Fiberglass Axe 600g HAX0206008

3/8" DR. 9PCS. Hex Bit Socket Set

INGCO Combination Pliers 100cm HCP08181

PLIERS SET PRECISON 2-PCS-ME545301

RIGHT CUTTING OFFSET SNIPS - 48-22-3079 shopping for tin snips, and  specifically for aviation snips, you'll  notice several types: straight-cut,  right-cut and left-cut snips, often  marked with yellow, green and red,  respectively. Each is suited to specific  cutting tasks. The forged steel jaws  of these left-cutting or right  -cutting snips are set at a 90- degree angle to allow easy  gripping when cutting sheet metal  in tight spaces or overhead.  The operator can follow tight circular  or square pattern left or right  cuts with either a pushing or  pulling motion.Left cut snips are for making  to the left and straight cuts.  Right cut snips are for making straight  and cuts to the right. Straight cut snips (not shown) are for making straight cuts  and shallow cuts to the right or left. Right hand tin snips are suitable  for cutting straight lines and cutting  off in an anti-clockwise direction.  Best suited for right handed use.  hand tin snips are suitable for cutting  off in a clockwise direction and for  cutting straight lines. Best suited for  left handed use. Types of Tin Sni They are also useful for  making long cuts through  sheet metal, should you  need to. However,  you're going to make a  long cut through sheet metal,  especially a straight one, a pair of snips with offset handles is the  way to go. Each color signifies a  different direction that  the snips are made to cut.  Red snips cut left. Yellow snips  cut straight or left and right. Green snips cut right. HVAC and sheet metal  pros agree: When making long,  straight cuts in thinner-gauge  sheet metal, tinner snips are the  way to go. They're a simple, economical,  and durable cutting solution for many sheet  metal and HVAC applicatioN.

1" DR. Dual Opening Budd. Heavy Duty