Screwking Hardware Corp.

GASoline Welder Generator Brand: Yohino Model: YHW210 DC Welder Max Current: 210AMP Rated Current: 180 Work Voltage: 28V Current Adjust Range: 90-210AMP AC Generator 3.3kVA Rated Current: 15AMP 220V/60Hz, Single Phase Engine Model: GX390 Type: Vertical Rated Power: 13HP/3600RPM Starting: Recoil/Electric Start Fuel Type: Gasoline Fuel Tank Capacity: 25L Oil Capacity: 1.1L Gasoline Welder Generator Brand: Yohino Model: YHW210 DC Welder Max Current: 210AMP Rated Current: 180 Work Voltage: 28V Current Adjust Range: 90-210AMP AC Generator 3.3kVA Rated Current: 15AMP 220V/60Hz, Single Phase Engine Model: GX390 Type: Vertical Rated Power: 13HP/3600RPM Starting: Recoil/Electric Start Fuel Type: Gasoline Fuel Tank Capacity: 25L Oil Capacity: 1.1L Generators with a low THD rating (6% or less) will have 'relatively' clean power and will thus be suitable for running inverter welders. A generator with a high THD rating (more than 6%) is likely to be a low quality unit and should not be used to run inverter welders. 3 kva to 4500 KVA Portable Welding Generators. ... 5 Kva Honda Powered Welding Generator, Warranty: 24 Months, Model Name/Number: GX390. ... Diesel Welding Generators. ... 1 Phase Portable Welding Machine 200 Amp, For Industrial, Automation Grade: Semi-Automatic.

A welder generator creates power for welding without reliance on mains electricity. Simply fill up the fuel tank, just as you would for a regular generator, and the welder generator will power your welding equipment wherever you need it. Differential Compound Generators are used for arc welding because of their drooping characteristics. The generator used for welding purposes should have high current and low vOltage which can be obtained by the differential compound generator. Gas welding works by feeding both oxygen and fuel gas out of the end of a torch to produce a highly concentrated flame that can melt metal. Material is melted at the seam between two parts to create what is known as a weld pool. The pool then cools and bonds the pieces together to form a strong joint.

YOHINO GASOLINE GENERATOR & WELDER - YHW20

Gasoline Generator OHV Forced Air-Cooled 4-Stroke

GASOLINE GENERATOR-BS1800

GASOLINE GENERATOR

GASOLINE GENERATOR

GASOLINE GENERATOR-BS6500

GASOLINE GENERATOR-BS6500ES

30mm body width hardened steel shackle brass padlock

40mm Hardened steel shackle brass padlock

Cylindrical Knob set- Satin stainless steel

HINGES 3.0X3.0X2.0MM STAINLESS STEEL YLGMLPHINGES3

Single cylinder deadbolt - Satin stainless steel

Tubular Knobset - Satin stainless steel

Tubular Lever set - Satin nickel

RIGHT CUTTING OFFSET SNIPS - 48-22-3079 shopping for tin snips, and specifically for aviation snips, you'll notice several types: straight-cut, right-cut and left-cut snips, often marked with yellow, green and red, respectively. Each is suited to specific cutting tasks. The forged steel jaws of these left-cutting or right -cutting snips are set at a 90- degree angle to allow easy gripping when cutting sheet metal in tight spaces or overhead. The operator can follow tight circular or square pattern left or right cuts with either a pushing or pulling motion.Left cut snips are for making to the left and straight cuts. Right cut snips are for making straight and cuts to the right. Straight cut snips (not shown) are for making straight cuts and shallow cuts to the right or left. Right hand tin snips are suitable for cutting straight lines and cutting off in an anti-clockwise direction. Best suited for right handed use. hand tin snips are suitable for cutting off in a clockwise direction and for cutting straight lines. Best suited for left handed use. Types of Tin Sni They are also useful for making long cuts through sheet metal, should you need to. However, you're going to make a long cut through sheet metal, especially a straight one, a pair of snips with offset handles is the way to go. Each color signifies a different direction that the snips are made to cut. Red snips cut left. Yellow snips cut straight or left and right. Green snips cut right. HVAC and sheet metal pros agree: When making long, straight cuts in thinner-gauge sheet metal, tinner snips are the way to go. They're a simple, economical, and durable cutting solution for many sheet metal and HVAC applicatioN.

A&TK Pen Light / Portable Flash Light

BM Series Hybrid Model

Headlights G Series

Power Bank Lantern

Rechargeable Angle Head Work Lights

Rechargeable Floodlights

Rechargeable Work Lights

German Type Grafting Knife

Conveying raw water and distribution of treated water in many rural water supply schemes, where the requirement of water is limited.

GI STUD BOLT FULLY THREADED ROD

Glass Holder

Glass Holder

Glass Holder