You have no items in your shopping cart.

Power & Hand Tools

Filters
per page
The majority of angle grinders have a fixed speed. Most 4-½-inch models run at 10,000 or 11,000 rpm. The said, 7-inch and 9-inch models run between 5,000 and 8,000 rpm. A few angle grinders have variable speed and can run slow enough for polishing or buffing. Grinder's come in lots of different disc sizes, but the most common sizes are 115mm (4 ½”) and 230mm (9”). You can purchase different discs/heads/ wheels depending on the task you want to complete - just make sure they're the right size for your grinder! 4' (100mm) angle grinders, as the name suggests, accept grinding discs up to 100mm in size. These grinders are relatively small in size, and are suitable for smaller jobs. The size of disc that the grinder can accept dictates the depth of cut that the grinder can achieve. Complete various grinding applications and get fast material removal with the 9-in. 4HP Angle Grinder. Featuring a high-powered motor with overload protection, this grinder delivers 6,500 rpm for tough jobs. The GA9060 weighs only 5.5 Kg and is built with comfort and ergonomic features for extended use. The grinder features an ergonomic rubberised handle with trigger switch, and the gear housing can be positioned every 90 degrees for operator convenience.
₱125,750.00 ₱100,600.00
utility knives snaps off in segments to remove worn cutting edges and expose sharp ones. Their sliding lever moves the blade strip into and out of the knife handle to retract and extend the cutting edge. A utility knife is generally six inches long and works well for slicing fruit, tender pieces of meat, or sandwiches. As the “knife of all trades,” it's a handy go-to for the everyday chef. “Snap-off blades have so many advantages: they allow for longer blade exposure; they're convenient, safer, versatile and always ready to use – and you'll have quick access to fresh, always-sharp blades. OLFA® STAINLESS STEEL™ blades are sharper than most other snap-off blades in the world, and rust-proof. This makes them perfectly suitable when things can get a little wet or moist. Utility knives are used to cut and trim a variety of building materials including: drywall, felt paper, wallpaper, rope & twine, plastic sheet material, fiberglass insulation and more. They can be divided into 3 general categories, Retractable Blade, Fixed Blade and Snap-off Blade. Utility knives usually only expose about 3/4-inch of the blade, so you have a limited cutting depth. Snap-offs retract around a couple of inches if you need to make a deeper cut in something like foam insulation.
₱905.00 ₱724.00
3 Way Screwdriver Tester
₱128.00
The majority of angle grinders have a fixed speed. Most 4-½-inch models run at 10,000 or 11,000 rpm. The said, 7-inch and 9-inch models run between 5,000 and 8,000 rpm. A few angle grinders have variable speed and can run slow enough for polishing or buffing. Grinder's come in lots of different disc sizes, but the most common sizes are 115mm (4 ½”) and 230mm (9”). You can purchase different discs/heads/ wheels depending on the task you want to complete - just make sure they're the right size for your grinder! 4' (100mm) angle grinders, as the name suggests, accept grinding discs up to 100mm in size. These grinders are relatively small in size, and are suitable for smaller jobs. The size of disc that the grinder can accept dictates the depth of cut that the grinder can achieve. Complete various grinding applications and get fast material removal with the 9-in. 4HP Angle Grinder. Featuring a high-powered motor with overload protection, this grinder delivers 6,500 rpm for tough jobs. The GA9060 weighs only 5.5 Kg and is built with comfort and ergonomic features for extended use. The grinder features an ergonomic rubberised handle with trigger switch, and the gear housing can be positioned every 90 degrees for operator convenience.
₱165,000.00 ₱132,000.00
The majority of angle grinders have a fixed speed. Most 4-½-inch models run at 10,000 or 11,000 rpm. The said, 7-inch and 9-inch models run between 5,000 and 8,000 rpm. A few angle grinders have variable speed and can run slow enough for polishing or buffing. Grinder's come in lots of different disc sizes, but the most common sizes are 115mm (4 ½”) and 230mm (9”). You can purchase different discs/heads/ wheels depending on the task you want to complete - just make sure they're the right size for your grinder! 4' (100mm) angle grinders, as the name suggests, accept grinding discs up to 100mm in size. These grinders are relatively small in size, and are suitable for smaller jobs. The size of disc that the grinder can accept dictates the depth of cut that the grinder can achieve. Complete various grinding applications and get fast material removal with the 9-in. 4HP Angle Grinder. Featuring a high-powered motor with overload protection, this grinder delivers 6,500 rpm for tough jobs. The GA9060 weighs only 5.5 Kg and is built with comfort and ergonomic features for extended use. The grinder features an ergonomic rubberised handle with trigger switch, and the gear housing can be positioned every 90 degrees for operator convenience.
₱425,000.00 ₱340,000.00
32-Piece Socket Set
₱2,621.00
32-Piece Socket Set
₱3,030.00
What is a demolition hammer? The demolition hammer is one of the power tools specifically designed for the demolition of the structure. It is also known as stomping hammers. Demolition hammer tools are strong enough to break down various materials such as wooden walls, concrete surfaces and tile flooring. Jackhammers, also known as demolition hammers or concrete breakers, are the primary tool in the breaking of old or non-standard structures and are a must-have for construction and renovation projects that often involve tearing down concrete slabs, tiles, or brick walls. A hammer drill, also known as a percussion drill or impact drill, is a power tool used chiefly for drilling in hard materials. It is a type of rotary drill with an impact mechanism that generates a hammering motion. Hammers are powerful enough to break up blocks of brick and concrete with ease. Our breaker hammers work with many Cat machines, meaning you can quickly transform your existing equipment into a robust demolition tool just by renting a breaker hammer. It is perfect for demolition, trenching, chipping, breaking holes in concrete, block, brick, tile stucco, housing foundation removal, concrete slab , oil chimney and much more! SDS is short for Slotted Drive Shaft or Slotted Drive System. These drills are typically used for heavy-duty drilling into materials such as brick, stone, oncrete and other types of masonry. Unlike regular drills, they have a SDS is short for Slotted Drive Shaft or Slotted Drive System. These drills are typically u sed for heavy-duty drilling into materials such as brick, stone, concrete and other types of masonry. Unlike regular drills, they have a unique design that provides a high level of power during drilling.
₱33,125.00 ₱26,500.00
They are completely different ; impact drivers provide torsional (rotational) impulses which act to drive the fastener clockwise as the screw advances into the material, percussion (hammer drill) provides linear impulses along the axis of the bit that act to micro-shatter the substrate (typically masonry) being drilled . A hammer drill works at a lower stroke rate, but with significantly greater impact energy than a percussion drill. This enables work to be completed more quickly. Hammer drilling in concrete requires less force than percussion drilling. An impact drill uses lateral percussion (from the side, in a circular motion). Once the drill senses that torque is needed , the drill uses impact to twist the screw into the surface. In short, an impact drill is used for driving screws and bolts that require a higher torque. Impact drivers produce lots of rotational force, capable of driving the largest wood screws in seconds. Internal mechanisms allow impact drivers to produce more torque than drills, and in quick bursts. These bursts or “impacts” happen up to 50 times a second, giving impact drivers their name. Can you use an impact driver to drill into concrete? If you drill holes that are less than 1/4 inch, an impact driver can help drill through concrete and brick. These tools have a massive amount of torque. However, they are not built to be used like hammer or regular drills. Percussion drilling is the perfect choice if you need to execute drilling in hard soils. Hard soil has layers of rubble or stones and percussion drilling can effectively drill through it. It is suitable for research on soil pollution, grain size distribution, general soil classification, and profile description. Percussion drilling is a drilling method in which a heavy hammering or cutting bit is attached to a cable and inserted into the borehole. The heavy bit or hammer is repeatedly lifted and dropped, thus boring through the earth. The hammer is made of hardened steel with carbide on the chisel -shaped bit.
₱78,750.00 ₱63,000.00
They are completely different ; impact drivers provide torsional (rotational) impulses which act to drive the fastener clockwise as the screw advances into the material, percussion (hammer drill) provides linear impulses along the axis of the bit that act to micro-shatter the substrate (typically masonry) being drilled . A hammer drill works at a lower stroke rate, but with significantly greater impact energy than a percussion drill. This enables work to be completed more quickly. Hammer drilling in concrete requires less force than percussion drilling. An impact drill uses lateral percussion (from the side, in a circular motion). Once the drill senses that torque is needed , the drill uses impact to twist the screw into the surface. In short, an impact drill is used for driving screws and bolts that require a higher torque. Impact drivers produce lots of rotational force, capable of driving the largest wood screws in seconds. Internal mechanisms allow impact drivers to produce more torque than drills, and in quick bursts. These bursts or “impacts” happen up to 50 times a second, giving impact drivers their name. Can you use an impact driver to drill into concrete? If you drill holes that are less than 1/4 inch, an impact driver can help drill through concrete and brick. These tools have a massive amount of torque. However, they are not built to be used like hammer or regular drills. Percussion drilling is the perfect choice if you need to execute drilling in hard soils. Hard soil has layers of rubble or stones and percussion drilling can effectively drill through it. It is suitable for research on soil pollution, grain size distribution, general soil classification, and profile description. Percussion drilling is a drilling method in which a heavy hammering or cutting bit is attached to a cable and inserted into the borehole. The heavy bit or hammer is repeatedly lifted and dropped, thus boring through the earth. The hammer is made of hardened steel with carbide on the chisel -shaped bit.
₱97,500.00 ₱78,000.00
4 Speed Magnetic Drilling Machine
₱182,000.00 ₱280,000.00
4 Speed Magnetic Drilling Machine
₱125,645.00 ₱193,300.00
4 Speed Magnetic Drilling Machine
₱150,995.00 ₱232,300.00
The best fuel for 4 cycle engines is ethanol free. Even though ethanol free fuel does not deteriorate carburetors like gas with ethanol , we strongly recommend, running the engine until the tank is out of gas, so only put into the tank the amount of gas you feel you will use. A brushcutter (also called a brush saw, clearing saw or gasoline goat) is a powered garden or agricultural tool used to trim weeds, small trees, and other foliage not accessible by a lawn mower or rotary mower. Various blades or trimmer heads can be attached to the machine for specific applications. Generally brush cutters function on two types of engine, either a two-stroke or a four-stroke engine. Two-stroke engines are usually lighter, but somewhat harder to start and a bit more inefficient than a four-stroke engine. Although four-stroke engines are stronger, they are more expensive and not available much.
₱31,750.00 ₱25,400.00
40 Piece Tap And Die Set-metric And Unc
₱2,400.00
DEWALT DIE GRINDER , ONE- TOUCH GUARD, PADDLE SWITCH , 400W, 6MM, DWE886P-B1
₱13,125.00
They are completely different ; impact drivers provide torsional (rotational) impulses which act to drive the fastener clockwise as the screw advances into the material, percussion (hammer drill) provides linear impulses along the axis of the bit that act to micro-shatter the substrate (typically masonry) being drilled . A hammer drill works at a lower stroke rate, but with significantly greater impact energy than a percussion drill. This enables work to be completed more quickly. Hammer drilling in concrete requires less force than percussion drilling. An impact drill uses lateral percussion (from the side, in a circular motion). Once the drill senses that torque is needed , the drill uses impact to twist the screw into the surface. In short, an impact drill is used for driving screws and bolts that require a higher torque. Impact drivers produce lots of rotational force, capable of driving the largest wood screws in seconds. Internal mechanisms allow impact drivers to produce more torque than drills, and in quick bursts. These bursts or “impacts” happen up to 50 times a second, giving impact drivers their name. Can you use an impact driver to drill into concrete? If you drill holes that are less than 1/4 inch, an impact driver can help drill through concrete and brick. These tools have a massive amount of torque. However, they are not built to be used like hammer or regular drills. Percussion drilling is the perfect choice if you need to execute drilling in hard soils. Hard soil has layers of rubble or stones and percussion drilling can effectively drill through it. It is suitable for research on soil pollution, grain size distribution, general soil classification, and profile description. Percussion drilling is a drilling method in which a heavy hammering or cutting bit is attached to a cable and inserted into the borehole. The heavy bit or hammer is repeatedly lifted and dropped, thus boring through the earth. The hammer is made of hardened steel with carbide on the chisel -shaped bit.
₱100,000.00 ₱80,000.00
40T SAW BLADE FINE WOOD CUTS FOR MTCS1400 CIRCULAR SAW-ARGMTCS1400SB40T
₱875.00
42-Piece Electricians Tool Kit
₱3,070.00
They are completely different ; impact drivers provide torsional (rotational) impulses which act to drive the fastener clockwise as the screw advances into the material, percussion (hammer drill) provides linear impulses along the axis of the bit that act to micro-shatter the substrate (typically masonry) being drilled . A hammer drill works at a lower stroke rate, but with significantly greater impact energy than a percussion drill. This enables work to be completed more quickly. Hammer drilling in concrete requires less force than percussion drilling. An impact drill uses lateral percussion (from the side, in a circular motion). Once the drill senses that torque is needed , the drill uses impact to twist the screw into the surface. In short, an impact drill is used for driving screws and bolts that require a higher torque. Impact drivers produce lots of rotational force, capable of driving the largest wood screws in seconds. Internal mechanisms allow impact drivers to produce more torque than drills, and in quick bursts. These bursts or “impacts” happen up to 50 times a second, giving impact drivers their name. Can you use an impact driver to drill into concrete? If you drill holes that are less than 1/4 inch, an impact driver can help drill through concrete and brick. These tools have a massive amount of torque. However, they are not built to be used like hammer or regular drills. Percussion drilling is the perfect choice if you need to execute drilling in hard soils. Hard soil has layers of rubble or stones and percussion drilling can effectively drill through it. It is suitable for research on soil pollution, grain size distribution, general soil classification, and profile description. Percussion drilling is a drilling method in which a heavy hammering or cutting bit is attached to a cable and inserted into the borehole. The heavy bit or hammer is repeatedly lifted and dropped, thus boring through the earth. The hammer is made of hardened steel with carbide on the chisel -shaped bit.
₱135,000.00 ₱108,000.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱11,125.00 ₱8,900.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱5,280.00 ₱6,600.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱10,312.00 ₱8,250.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱6,875.00 ₱5,500.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱10,725.00 ₱8,580.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱7,250.00 ₱5,800.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱11,500.00 ₱9,200.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱7,700.00 ₱6,160.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱11,275.00 ₱9,020.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱11,275.00 ₱9,020.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱9,350.00 ₱7,480.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱12,787.00 ₱10,230.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱9,500.00 ₱7,600.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱13,125.00 ₱10,500.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱16,250.00 ₱13,000.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱17,500.00 ₱14,000.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱25,000.00 ₱20,000.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱43,750.00 ₱3,500.00
The majority of angle grinders have a fixed speed. Most 4-½-inch models run at 10,000 or 11,000 rpm. The said, 7-inch and 9-inch models run between 5,000 and 8,000 rpm. A few angle grinders have variable speed and can run slow enough for polishing or buffing. Grinder's come in lots of different disc sizes, but the most common sizes are 115mm (4 ½”) and 230mm (9”). You can purchase different discs/heads/ wheels depending on the task you want to complete - just make sure they're the right size for your grinder! 4' (100mm) angle grinders, as the name suggests, accept grinding discs up to 100mm in size. These grinders are relatively small in size, and are suitable for smaller jobs. The size of disc that the grinder can accept dictates the depth of cut that the grinder can achieve. Complete various grinding applications and get fast material removal with the 9-in. 4HP Angle Grinder. Featuring a high-powered motor with overload protection, this grinder delivers 6,500 rpm for tough jobs. The GA9060 weighs only 5.5 Kg and is built with comfort and ergonomic features for extended use. The grinder features an ergonomic rubberised handle with trigger switch, and the gear housing can be positioned every 90 degrees for operator convenience.
₱43,068.00 ₱33,650.00
They are completely different ; impact drivers provide torsional (rotational) impulses which act to drive the fastener clockwise as the screw advances into the material, percussion (hammer drill) provides linear impulses along the axis of the bit that act to micro-shatter the substrate (typically masonry) being drilled . A hammer drill works at a lower stroke rate, but with significantly greater impact energy than a percussion drill. This enables work to be completed more quickly. Hammer drilling in concrete requires less force than percussion drilling. An impact drill uses lateral percussion (from the side, in a circular motion). Once the drill senses that torque is needed , the drill uses impact to twist the screw into the surface. In short, an impact drill is used for driving screws and bolts that require a higher torque. Impact drivers produce lots of rotational force, capable of driving the largest wood screws in seconds. Internal mechanisms allow impact drivers to produce more torque than drills, and in quick bursts. These bursts or “impacts” happen up to 50 times a second, giving impact drivers their name. Can you use an impact driver to drill into concrete? If you drill holes that are less than 1/4 inch, an impact driver can help drill through concrete and brick. These tools have a massive amount of torque. However, they are not built to be used like hammer or regular drills. Percussion drilling is the perfect choice if you need to execute drilling in hard soils. Hard soil has layers of rubble or stones and percussion drilling can effectively drill through it. It is suitable for research on soil pollution, grain size distribution, general soil classification, and profile description. Percussion drilling is a drilling method in which a heavy hammering or cutting bit is attached to a cable and inserted into the borehole. The heavy bit or hammer is repeatedly lifted and dropped, thus boring through the earth. The hammer is made of hardened steel with carbide on the chisel -shaped bit.
₱178,750.00 ₱14,300.00
They are completely different ; impact drivers provide torsional (rotational) impulses which act to drive the fastener clockwise as the screw advances into the material, percussion (hammer drill) provides linear impulses along the axis of the bit that act to micro-shatter the substrate (typically masonry) being drilled . A hammer drill works at a lower stroke rate, but with significantly greater impact energy than a percussion drill. This enables work to be completed more quickly. Hammer drilling in concrete requires less force than percussion drilling. An impact drill uses lateral percussion (from the side, in a circular motion). Once the drill senses that torque is needed , the drill uses impact to twist the screw into the surface. In short, an impact drill is used for driving screws and bolts that require a higher torque. Impact drivers produce lots of rotational force, capable of driving the largest wood screws in seconds. Internal mechanisms allow impact drivers to produce more torque than drills, and in quick bursts. These bursts or “impacts” happen up to 50 times a second, giving impact drivers their name. Can you use an impact driver to drill into concrete? If you drill holes that are less than 1/4 inch, an impact driver can help drill through concrete and brick. These tools have a massive amount of torque. However, they are not built to be used like hammer or regular drills. Percussion drilling is the perfect choice if you need to execute drilling in hard soils. Hard soil has layers of rubble or stones and percussion drilling can effectively drill through it. It is suitable for research on soil pollution, grain size distribution, general soil classification, and profile description. Percussion drilling is a drilling method in which a heavy hammering or cutting bit is attached to a cable and inserted into the borehole. The heavy bit or hammer is repeatedly lifted and dropped, thus boring through the earth. The hammer is made of hardened steel with carbide on the chisel -shaped bit.
₱161,250.00 ₱129,000.00
They are completely different ; impact drivers provide torsional (rotational) impulses which act to drive the fastener clockwise as the screw advances into the material, percussion (hammer drill) provides linear impulses along the axis of the bit that act to micro-shatter the substrate (typically masonry) being drilled . A hammer drill works at a lower stroke rate, but with significantly greater impact energy than a percussion drill. This enables work to be completed more quickly. Hammer drilling in concrete requires less force than percussion drilling. An impact drill uses lateral percussion (from the side, in a circular motion). Once the drill senses that torque is needed , the drill uses impact to twist the screw into the surface. In short, an impact drill is used for driving screws and bolts that require a higher torque. Impact drivers produce lots of rotational force, capable of driving the largest wood screws in seconds. Internal mechanisms allow impact drivers to produce more torque than drills, and in quick bursts. These bursts or “impacts” happen up to 50 times a second, giving impact drivers their name. Can you use an impact driver to drill into concrete? If you drill holes that are less than 1/4 inch, an impact driver can help drill through concrete and brick. These tools have a massive amount of torque. However, they are not built to be used like hammer or regular drills. Percussion drilling is the perfect choice if you need to execute drilling in hard soils. Hard soil has layers of rubble or stones and percussion drilling can effectively drill through it. It is suitable for research on soil pollution, grain size distribution, general soil classification, and profile description. Percussion drilling is a drilling method in which a heavy hammering or cutting bit is attached to a cable and inserted into the borehole. The heavy bit or hammer is repeatedly lifted and dropped, thus boring through the earth. The hammer is made of hardened steel with carbide on the chisel -shaped bit.
₱178,750.00 ₱143,000.00
Ideal for fastening drywall and panels to wooden or metal studs. Removable depth sensitive “set and forget” nosepiece for consistent fastener depth
₱27,068.00
DEWALT D26676-B1 550W 1.5MM PORTABLE PLANER
₱17,188.00
59-Piece Electrician's Tool Kit
₱3,200.00
#2 Phillips is a common size and is designed for sheet rock screws, wood screws, and many machine screws. The Best Impact Driver Bits for Beginners and Professionals. An impact driver is an essential tool for any DIYer . It can tackle tough fastening jobs with ease, and it has the power to drive even the most stubborn screws or bolts. Klein's #2 Phillips slotted Screw-Holding Screwdriver provide positive gripping action to hold, start, and drive slotted screws in confined, hard-to-reach places. The unique blade design allows for both torquing and tightening of screws. An impact driver outputs higher torque levels than a drill, making it more efficient for quickly driving long, wide and large screws into tough materials. As a result, it significantly reduces your work time when large volumes of fasteners need to be secured. An impact drill uses lateral percussion (from the side, in a circular motion). Once the drill senses that torque is needed, the drill uses impact to twist the screw into the surface. In short, an impact drill is used for driving screws and bolts that require a higher torque.
₱557.00 ₱446.00
#2 Phillips is a common size and is designed for sheet rock screws, wood screws, and many machine screws. The Best Impact Driver Bits for Beginners and Professionals. An impact driver is an essential tool for any DIYer . It can tackle tough fastening jobs with ease, and it has the power to drive even the most stubborn screws or bolts. Klein's #2 Phillips slotted Screw-Holding Screwdriver provide positive gripping action to hold, start, and drive slotted screws in confined, hard-to-reach places. The unique blade design allows for both torquing and tightening of screws. An impact driver outputs higher torque levels than a drill, making it more efficient for quickly driving long, wide and large screws into tough materials. As a result, it significantly reduces your work time when large volumes of fasteners need to be secured. An impact drill uses lateral percussion (from the side, in a circular motion). Once the drill senses that torque is needed, the drill uses impact to twist the screw into the surface. In short, an impact drill is used for driving screws and bolts that require a higher torque.
₱557.00 ₱446.00
#2 Phillips is a common size and is designed for sheet rock screws, wood screws, and many machine screws. The Best Impact Driver Bits for Beginners and Professionals. An impact driver is an essential tool for any DIYer . It can tackle tough fastening jobs with ease, and it has the power to drive even the most stubborn screws or bolts. Klein's #2 Phillips slotted Screw-Holding Screwdriver provide positive gripping action to hold, start, and drive slotted screws in confined, hard-to-reach places. The unique blade design allows for both torquing and tightening of screws. An impact driver outputs higher torque levels than a drill, making it more efficient for quickly driving long, wide and large screws into tough materials. As a result, it significantly reduces your work time when large volumes of fasteners need to be secured. An impact drill uses lateral percussion (from the side, in a circular motion). Once the drill senses that torque is needed, the drill uses impact to twist the screw into the surface. In short, an impact drill is used for driving screws and bolts that require a higher torque.
₱557.00 ₱446.00
#2 Phillips is a common size and is designed for sheet rock screws, wood screws, and many machine screws. The Best Impact Driver Bits for Beginners and Professionals. An impact driver is an essential tool for any DIYer . It can tackle tough fastening jobs with ease, and it has the power to drive even the most stubborn screws or bolts. Klein's #2 Phillips slotted Screw-Holding Screwdriver provide positive gripping action to hold, start, and drive slotted screws in confined, hard-to-reach places. The unique blade design allows for both torquing and tightening of screws. An impact driver outputs higher torque levels than a drill, making it more efficient for quickly driving long, wide and large screws into tough materials. As a result, it significantly reduces your work time when large volumes of fasteners need to be secured. An impact drill uses lateral percussion (from the side, in a circular motion). Once the drill senses that torque is needed, the drill uses impact to twist the screw into the surface. In short, an impact drill is used for driving screws and bolts that require a higher torque. Shockwave™ Impact Driver Bits are engineered to be the Most Durable, Best Fitting driver bits on the market. The Wear Guard Tip™ delivers increased wear resistance which protects the fit over the life of the bit. The Shockzone™ is optimized for for each tip type and length of driver bit to absorb peak torque and prevent breaking. The Custom Alloy76™ has a customized steel and heat treatment per tip type to extend the life of the driver bits, providing up to 50X life vs. competitive impact driver bits. Shockwave™ driver bits are built to deliver extreme durability for the most demanding applications
₱557.00 ₱446.00
The magnetic bit holder is an indispensable accompaniment to any drill driver. It consists of a hexagonal steel bar, one end of which grips the chuck. The other end comes with a chrome steel cylinder into which any screwdriver bit will slot. A small magnet also prevents the bit from dropping out. The new locking bit holder feature two magnets to maximize magnetic transfer and holding power to the fastener and prevent drops. As with all SHOCKWAVE™ Impact Duty Accessories, each bit holder features an optimized SHOCK ZONE™ geometry to provide up to 30X longer life and absorb 3X more torque to prevent breakage. Work Environment a lighter weight mag drill is preferred if you are working high up in the air, etc. Space Limitations – If you are working in tight spaces a low-profile mag drill may be ideal, such as: The Hougen HMD130 Mag Drill or the Fein JMC Magforce 90 Mag Drill. Our SHOCKWAVE™ Impact Duty™ Magnetic Bit Holders are engineered for extreme durability and up to 30x life. The MILWAUKEE magnetic bit holders are made from proprietary steel, heat treated to control hardness. The SHOCKWAVE™ magnetic bit holders feature a powerful magnet, providing you with a secure grip and unyielding bit engagement . Each bit holder has a 2-piece construction for optimal assembly in abusive applications. Our SHOCKWAVE™ Impact Duty™ Magnetic Bit Holders have a C-ring to retain the insert bit and can now be used with Milwaukee SHOCKWAVE™ Impact Duty Insert Magnetic Nut Drivers (¼”, 5/16”, ⅜”, 7/16”, ½”). A "bit-holder" will often be magnetized to hold the bit in (and incidentally holding the screw as well) while the other two can be, but it's not as common. A "hex bit socket" or "nut driver" is probably more durable than a "bit holder" if it matters to you, for example if you're using a high torque impact driver.
₱1,185.00 ₱948.00
Filters Clear All
Min: ₱0.00 Max: ₱1,533,500.00
₱0 ₱1533500
Close